The first thing you want to do, before you even begin, is to pick a pony and pose. I picked the G1 Sugarberry Pose. To replicate the pony, knowledge of the anatomy is useful. Here is my pony:
visitors can't see pics , please
register or
loginA pony is basically made up of 3 circles and 5 rectangles. The rump is the biggest circle, the front is another, and the head is the smallest circle. The legs and muzzle are the rectangles. The back and belly are curved, and the hind legs have points and curves and the front legs have curves. The legs also vary in thickness, the base and hoof being bigger thicker than the middle. The neck gets thinner towards the head. Top portion of the bit that connects the head toward the muzzle is flat. The jaw is curved. Facing the front, the cheeks stick out. The ears are about as big as the cheeks and are turned slightly outwards. They resemble triangles.
I suggest you break your pony down like this so you can replicate the anatomy
With all your tools ready you can begin sculpting! I do my sculpts in order of least fragile to most fragile. First I make the body, then the head, then the legs. Let's start with the body!
visitors can't see pics , please
register or
loginTake a little oval of clay. You can roll it out into a log like shape.
visitors can't see pics , please
register or
loginUse your dotting tool to make it thinner in the middle. This also acts as the curve for the back. Be careful not to shape the belly, you want it to be a bit round. The sides should be shaped, though. The rump should be bigger than the front. You can mark the front with your dotting tool if you'd like
visitors can't see pics , please
register or
loginvisitors can't see pics , please
register or
loginJust keep working it until it looks they way you want. Remember to keep wetting and softening the clay. Since it's so tiny, the clay dries out very very quickly.
visitors can't see pics , please
register or
loginYou can also cut off a piece of staple and stick it in the front, allowing support for the neck. Leave it to dry for a while. Make sure to put your extra clay back in your sealed bag or whatever you use so it doesn't dry out. After it's dry, you can move on to the head!
visitors can't see pics , please
register or
loginTake a sphere of clay. This should be out the same size as the front sphere of the body. Take a another bit of clay. This should be smaller than the head, but not too small. Remember to keep the head and muzzle moist, adding water throughout will help the muzzle attach.
visitors can't see pics , please
register or
loginStart blending the muzzle into the head. If yours is too long like mine was, you can cut it. It looks weird at first, but keep going!
visitors can't see pics , please
register or
loginKeep blending and shaping. The muzzle should be visibly thinner than the head, but the top and bottom should curve into it. Look at your pony from different angles for reference. Keep working it back and forth.
visitors can't see pics , please
register or
loginHere, mine is about finished.
visitors can't see pics , please
register or
loginI added her smile and nostrils with my safety pin, pushing the bottom of the mouth a bit farther back.
visitors can't see pics , please
register or
loginPut her head on the staple and leave to dry. Here, after taking the pic, I accidentally broke her body, and I had to sculpt a new one.
visitors can't see pics , please
register or
loginStart adding some clay to her neck. Smooth a bit, add water, then put her head on.
visitors can't see pics , please
register or
loginSmooth the neck out. Adjust so the angle of the head is right. I don't know if you can see, but the staple I used for support is sticking out - not good. I used my pliers to remove it.
visitors can't see pics , please
register or
loginKeep working it back and forth and keep adding water. Sculpt the cheeks too.
visitors can't see pics , please
register or
loginTake two tiny balls of clay for the ears.
visitors can't see pics , please
register or
loginAttach them. To shape, pinch them until their shape is right, then use your dotting tool to make the inside of the ear. I know I keep saying this but keep adding water
visitors can't see pics , please
register or
loginNow... time for the legs... *dun dun dun* These are probably the hardest part. To begin, cut your snake of clay into four sections.
visitors can't see pics , please
register or
loginThe ends may look like this, but that can be fixed. Roll the pokey bits so none are sticking out:
visitors can't see pics , please
register or
loginAnd flatten with a clay knife or something like that. Do this with all four legs.
visitors can't see pics , please
register or
loginFor the hind legs, make a bend. Pinch around the point to make it sharper. Bend the top half of the leg up. Do this for both hind legs.
visitors can't see pics , please
register or
loginHere are all my legs. You may need to do the front legs differently depending on which pose you do.
visitors can't see pics , please
register or
loginAttaching the legs is the hard part. Take your dotting tool and make a small hole in the center of the top of the leg. Flare the sides and wet it. Stick it on the belly, and blend. You will need to do this for all four legs. You might need to redo some, it's tricky!
visitors can't see pics , please
register or
loginYou can see my legs are too long. I gave them a trim before moving on. You want to make sure they are even so she can stand.
visitors can't see pics , please
register or
loginAlmost there... Keep working them back and forth. If you add too much water like I did, just wait a bit. If you want to go the extra mile, add some indents to the bottoms of the hooves like actual G1s!
visitors can't see pics , please
register or
loginAnd I got done and she can stand, but I think you can see something wrong... Her head fell off! To reattach parts, wet the area and stick it on. Wait for it to dry, then add water and smooth. It there are any dents or misalignments, add some clay.
You can always bulk up or smooth down any area if need be. If you want, you can add hair but doing strands or sheets and paint. You can achieve detailed eyes and symbols using a staple to paint.
And with that, the body is complete! Keep in mind that in the pictures it looks fast, but it took me many hours over three days. Mini ponies require a lot of trial and error, patience, and perseverance. I hope to add more to the tutorial portion as I make a mold, cast, and make a bunch of ponies. Good luck if you decide to make one! If you have any questions feel free to ask
If you do decide to make one, I would love to see if you would like to share
I hope you enjoyed this post and found it useful! Thank you for reading (and yes I know this was long!)